Menu
Obsługa i pomoc
Materiały do pobrania

Materiały do pobrania

Biblioteka techniczna Megger zapewnia dostęp do szeregu dodatkowych treści i zasobów, takich jak przewodniki techniczne, katalogi i wiele innych. Użyj filtrów, aby przeglądać określone treści lub zawęź wyszukiwanie do konkretnego obszaru wyszukiwań.

Jeśli potrzebujesz więcej materiałów, zdjęć, instrukcji załóż konto aby zdobyć potrzebne materiały.

Filtruj wg typu zastosowania
    Wyświetla pozycje 1 - 10 z 17 ogółem
Measuring cable impedance with SVERKER900
This is an easy solution to measure the impedance values for cables, the values are used for calculation of compensation factor in distance protection.The compensation factor is first theoretically calculated and these values can now be compared with the measured values.
Opublikowano 14 grudnia 2020
Pobierz wersję PDF
Case Study on IDAX300 and VAX020
The Power Grid Corporation of India Limited (PGCIL) is an Indian state-owned company headquartered in Gurugram (North India) engaged mainly in Trans-mission  of  Power  and  transmits  about  50%  of  the  total  power  generated  in  India  on  its  transmission  network.  The  company  owns  and  operates  about  1,61,790  circuit  kms  of  transmission  lines  at  800/765 kV,  400 kV,  220 kV  &  132 kV EHVAC and +500 kV HVDC levels and 248 sub-stations. Also, it has the transformation capacity of about 396 825 MVA as of 30th November 2019.
Opublikowano 26 sierpnia 2020
Pobierz wersję PDF
TTRU3 Factory ratio testing of power transformer
Transformer equipment manufacturers (OEMs) have a critical need to measure true ratio, as they must confirm proper manufacture of their transformers during construction and final assembly. Improper construction has consequences of higher cost, late delivery, and poor quality. The ability of a ratio instrument to be used for all steps involved makes it a practical valueto OEMs because only one instrument is purchased and used throughout each stage. Only the most reliable and accurate instruments make it to the factory floor. Winding stack under constructionre used: Art Mandigo Winding Service.
Opublikowano 3 sierpnia 2020
Pobierz wersję PDF
Testing frequency relays with SVERKER900 considering the IEC 60255-181 standard
This application note is more than a description of how to use SVERKER 900 for testing frequency relays. It also wantsto spread the knowledge about IEC standardization in relay protection. Many engineers often associate theIEC series of protection standards IEC 60255-1xx1to relay type testing, and believe that they do not need to have competence about this series of standards. This is a misunderstanding: many of the concepts, definitions and test procedures described in thestandards are there to be used in relay technique, no matter if the role is relay manufacturer, user, or commissioning / maintenance testing engineer ([2], [3]).
Opublikowano 30 lipca 2020
Pobierz wersję PDF
DLRO2: Tryb pomiaru przy długich przewodach
Przez wiele lat metoda4-przewodowa pozostawała standardem w mierzeniu małych rezystancji. Jej główną zaletą jest eliminacjarezystancji przewodów pomiarowych. Co jednak w przypadku, gdy wymagane jest zastosowanie długich przewodówpomiarowych?
Opublikowano 27 lipca 2020
Pobierz wersję PDF
TTRU3 Phase Shifting Transformer App note
The is capable of performing turns ratio tests on any phase shifting transformer by allow-ing for phase shifts to be entered with respect to the secondary winding. But with all of the differ-ent ways phase shift is expressed, how do you know if the entered phase shift value is correct?
Opublikowano 22 sierpnia 2019
Pobierz wersję PDF
SVERKER900 - Testing-ROCOF-protection
Rate Of Change Of Frequency (ROCOF) protection is used in distributed or embedded generation schemes, where a local generator is connected directly to the distribution network, as specified in national standards such as Ansi 81R or G59/3
Opublikowano 15 maja 2019
Pobierz wersję PDF
SVERKER900 - Testing ABB Trip Circuit Supervision relay
Check trip on relay with ABB supervision relay
Opublikowano 15 maja 2019
Pobierz wersję PDF
SVERKER900 - Testing impedance based protection
The impedance measurement schemes are widely used for protection of different assets within electric power systems. Relay protection devices utilizing such schemes are benefiting from continuous monitoring of both voltage and current quantities within the protected circuit and the calculated impedance value is employed to determine whether the circuit is operating in a normal condition or not.
Opublikowano 15 maja 2019
Pobierz wersję PDF
SVERKER900 - Testing negative sequence overcurrent protection
Unbalance phase currents in a power system that exceed the allowable normal operation limit can indicate abnormal condition or even existence of fault(s) in the system. The operating principal unbalance over current protection is normally based on measurement of negative sequence component of unbalance phase currents. Similar to phase over current protection, normally a pick up (start) threshold and a definite time delay for operation can be set.
Opublikowano 15 maja 2019
Pobierz wersję PDF
  • 1
  • 2
  • >
  • Wyświetla pozycje 1 - 10 z 17 ogółem